• ISSN 1001-1455  CN 51-1148/O3
  • EI、Scopus、CA、JST、EBSCO、DOAJ收录
  • 力学类中文核心期刊
  • 中国科技核心期刊、CSCD统计源期刊

空孔底部装药延迟起爆对深孔直眼掏槽成腔效果的影响

叶福,  程兵,  汪泉,  程扬帆,  任帅,  高翔,  宗琦,  王梦想

叶福, 程兵, 汪泉, 程扬帆, 任帅, 高翔, 宗琦, 王梦想. 空孔底部装药延迟起爆对深孔直眼掏槽成腔效果的影响[J]. 爆炸与冲击. doi: 10.11883/bzycj-2025-0394
引用本文: 叶福, 程兵, 汪泉, 程扬帆, 任帅, 高翔, 宗琦, 王梦想. 空孔底部装药延迟起爆对深孔直眼掏槽成腔效果的影响[J]. 爆炸与冲击. doi: 10.11883/bzycj-2025-0394
YE Fu, CHENG Bing, WANG Quan, CHENG Yangfan, REN Shuai, GAO Xiang, ZONG Qi, WANG Mengxiang. Impacts of delayed detonation of empty hole bottom charge on the cavity forming effects of deep hole parallel cutting[J]. Explosion And Shock Waves. doi: 10.11883/bzycj-2025-0394
Citation: YE Fu, CHENG Bing, WANG Quan, CHENG Yangfan, REN Shuai, GAO Xiang, ZONG Qi, WANG Mengxiang. Impacts of delayed detonation of empty hole bottom charge on the cavity forming effects of deep hole parallel cutting[J]. Explosion And Shock Waves. doi: 10.11883/bzycj-2025-0394

空孔底部装药延迟起爆对深孔直眼掏槽成腔效果的影响

doi: 10.11883/bzycj-2025-0394
基金项目: 安徽省自然科学基金(2408085QA029);深部煤炭安全开采与环境保护全国重点实验室开放基金(2025YB011);深部煤矿采动响应与灾害防控国家重点实验室开放基金(SKLMRDPC23KF05);安徽理工大学研究生创新基金(2025cx2099);国家自然科学基金(52504075)
详细信息
    作者简介:

    叶 福(2000- ),男,硕士研究生,17684175178@163.com

    通讯作者:

    程 兵(1995- ),男,博士,讲师,2022053@aust.edu.cn

  • 中图分类号: O389; TD235; TJ51

Impacts of delayed detonation of empty hole bottom charge on the cavity forming effects of deep hole parallel cutting

  • 摘要: 针对深孔钻爆掘进中直眼掏槽成腔效率低下的难题,提出空孔底部装药延迟起爆的解决方案:首先通过理论分析、模型试验及数值模拟,研究了空孔底部装药延迟起爆对成腔效率的影响;然后结合岩石抛掷过程的高速影像与数值模拟,揭示了两种炮孔装药爆破协同作用下的成腔机制;最后开展现场试验验证其实际应用效果。结果表明:空孔底部装药延迟起爆可以大幅消除槽腔底部的残留根底,使得成腔效率从80%以下提升到95%以上;在掏槽孔爆破阶段,围岩夹制作用导致槽腔残留根底,但新生的临空面有利于后续阶段根底的抛掷;在空孔底部装药爆破时,由于围岩夹制作用减弱,根底抛掷速度较上部岩体高约2.0 m/s,可以实现根底的有效抛除与良好的成腔效果。与传统直眼掏槽技术相比,采用空孔底部装药延迟起爆方法,循环进尺提高了0.35 m,炸药单耗降低了0.43 kg/m3,证实了改进后的直眼掏槽技术有助于提升掘进效率和降低掘进成本。
  • 图  1  装药形式示意图

    Figure  1.  Diagram of charge forms

    图  2  成腔效果示意图

    Figure  2.  Diagram of cavity forming effects

    图  3  模型试验主要步骤

    Figure  3.  Main steps of model experiments

    图  4  掏槽孔装药爆破岩石抛掷历程

    Figure  4.  Rock throwing process during cutting hole charge blasting

    图  5  空孔装药爆破岩石抛掷历程

    Figure  5.  Rock throwing process during empty hole charge blasting

    图  6  抛掷速度对比

    Figure  6.  Comparison of throwing velocity

    图  7  槽腔深度测量

    Figure  7.  Measurement of cutting cavity depth

    图  8  槽腔深度对比

    Figure  8.  Comparison of cutting cavity depth

    图  9  岩体数值模型示意图

    Figure  9.  Diagram of rock mass numerical model

    图  10  掏槽孔装药爆破过程

    Figure  10.  Process of cutting hole charge blasting

    图  11  空孔装药爆破过程

    Figure  11.  Process of empty hole charge blasting

    图  12  岩石粒子抛掷速度随深度变化曲线

    Figure  12.  Curve of rock particle throwing velocity with depth variation

    图  13  炮孔布置(单位:mm)

    Figure  13.  Blasting hole layout (unit: mm)

    图  14  典型残孔深度

    Figure  14.  Typical residual hole depth

    表  1  水泥砂浆物理力学参数

    Table  1.   Physical and mechanical parameters of cement mortar

    密度/(kg·m−3)泊松比弹性模量/GPa抗压强度/MPa抗拉强度/MPa
    24400.2426.525.42.0
    下载: 导出CSV

    表  2  炸药材料参数

    Table  2.   Materials parameters of explosive

    密度/(kg·m−3) 爆速/(m·s−1) Ae/GPa Be/GPa R1 R2 ω E0/GPa
    1820 8300 908.47 19.12 4.92 1.41 0.31 10.00
    下载: 导出CSV

    表  3  岩石本构参数

    Table  3.   Constitutive parameters of rock

    A B C N ε0 εfmin Sfmax pc/MPa
    0.66 1.34 0.0018 0.845 1.0×10−6 0.01 80 13.8
    μc pl/GPa μl K1/GPa K2/GPa K3/GPa D1 D2
    0.0075 1.096 0.15 85 −171 208 0.04 1.0
     注:A、B、C、N分别为内聚力系数、压力硬化系数、率相关系数、压力硬化指数;ε0为参考应变率;εfmin为破裂累积塑性应变;Sfmax为特征化最大强度;pc、μc为压垮时的静水压力、体积应变;pl、μl为压实时的静水压力和体积应变;K1、K2、K3为压力参数;D1、D2为损伤常数。
    下载: 导出CSV

    表  4  掘进断面相关参数

    Table  4.   Parameters of driving section

    宽度/m高度/m面积/m2岩石坚固性系数
    5.14.219.5848~10
    下载: 导出CSV

    表  5  爆破参数

    Table  5.   Blasting parameters

    炮孔类型炮孔数目孔径/mm孔深/m装药量/kg起爆顺序
    单孔小计
    中心空孔1903.01.21.22
    掏槽孔4422.82.49.61
    辅助孔110422.52.222.03
    辅助孔211422.51.819.84
    辅助孔315422.51.827.05
    帮孔10422.51.212.06
    顶孔11422.51.213.26
    底孔9422.51.412.67
    总计71−−−117.4−
    下载: 导出CSV

    表  6  全断面爆破效果统计

    Table  6.   Statics of full-section blasting effects

    评价指标循环进尺/m炸药单耗/(kg·m−3)
    原方案1.973.01
    优化方案2.322.58
    差值0.35−0.43
    下载: 导出CSV
  • [1] WU H J, JIA J Y, GONG M, et al. Optimization of relief hole blasting satisfying synergistic constraints of rock-breaking area and hole-bottom minimum burden [J]. Tunnelling and Underground Space Technology, 2024, 154: 106074. DOI: 10.1016/j.tust.2024.106074.
    [2] 王雁冰, 张航, 杨仁树, 等. 掏槽孔超深深度对爆破效果的影响 [J]. 工程科学学报, 2023, 45(2): 182–194. DOI: 10.13374/j.issn2095-9389.2021.11.30.006.

    WANG Y B, ZHANG H, YANG R S, et al. Experiment study on overdepth coefficient of the cut hole in coal mine roadway excavation blasting [J]. Chinese Journal of Engineering, 2023, 45(2): 182–194. DOI: 10.13374/j.issn2095-9389.2021.11.30.006.
    [3] 程兵, 汪海波, 宗琦, 等. 基于切缝装药定向预裂的中深孔掏槽爆破研究 [J]. 振动与冲击, 2023, 42(3): 322–329. DOI: 10.13465/j.cnki.jvs.2023.03.037.

    CHENG B, WANG H B, ZONG Q, et al. Mid-deep hole cutting blasting technology based on slit charge directional presplitting [J]. Journal of Vibration and Shock, 2023, 42(3): 322–329. DOI: 10.13465/j.cnki.jvs.2023.03.037.
    [4] 李祥龙, 张志平, 王建国, 等. 双空孔间距对爆破槽腔断面大小的影响 [J]. 爆炸与冲击, 2022, 42(11): 115201. DOI: 10.11883/bzycj-2021-0471.

    LI X L, ZHANG Z P, WANG J G, et al. Influence of double empty hole spacing on section size of blasting chamber [J]. Explosion and Shock Waves, 2022, 42(11): 115201. DOI: 10.11883/bzycj-2021-0471.
    [5] 李启月, 吴正宇, 黄武林. 直眼掏槽空孔效应的计算模型改进与分析 [J]. 采矿与安全工程学报, 2018, 35(5): 925–930. DOI: 10.13545/j.cnki.jmse.2018.05.007.

    LI Q Y, WU Z Y, HUANG W L. Improvement and analysis of calculation model for empty hole effect in parallel cut [J]. Journal of Mining & Safety Engineering, 2018, 35(5): 925–930. DOI: 10.13545/j.cnki.jmse.2018.05.007.
    [6] 汪海波, 宗琦, 赵要才. 立井大直径中空孔直眼掏槽爆炸应力场数值模拟分析与应用 [J]. 岩石力学与工程学报, 2015, 34(S1): 3223–3229. DOI: 10.13722/j.cnki.jrme.2014.0296.

    WANG H B, ZONG Q, ZHAO Y C. Numerical analysis and application of large diameter cavity parallel cut blasting stress field in vertical shaft [J]. Chinese Journal of Rock Mechanics and Engineering, 2015, 34(S1): 3223–3229. DOI: 10.13722/j.cnki.jrme.2014.0296.
    [7] 张召冉, 左进京, 郭义先. 爆炸载荷下空孔及其缺陷对裂纹扩展影响机理研究 [J]. 振动与冲击, 2019, 38(18): 115–121. DOI: 10.13465/j.cnki.jvs.2019.18.016.

    ZHANG Z R, ZUO J J, GUO Y X. Effects of empty hole and its defects on the crack propagation under explosive loading [J]. Journal of Vibration and Shock, 2019, 38(18): 115–121. DOI: 10.13465/j.cnki.jvs.2019.18.016.
    [8] 陶子豪, 李祥龙, 胡启文, 等. 掏槽爆破成腔空孔效应数值模拟研究与分析 [J]. 兵工学报, 2024, 45(12): 4246–4258. DOI: 10.12382/bgxb.2024.0250.

    TAO Z H, LI X L, HU Q W, et al. Study and analysis on numerical simulation of empty hole effect induced by cutting blasting [J]. Acta Armamentarii, 2024, 45(12): 4246–4258. DOI: 10.12382/bgxb.2024.0250.
    [9] 左进京, 杨仁树, 肖成龙, 等. 煤矿井巷中空孔掏槽爆破模型实验研究 [J]. 矿业科学学报, 2018, 3(4): 335–341. DOI: 10.19606/j.cnki.jmst.2018.04.003.

    ZUO J J, YANG R S, XIAO C L, et al. Model test of empty hole cut blasting in coal mine rock drivage [J]. Journal of Mining Science and Technology, 2018, 3(4): 335–341. DOI: 10.19606/j.cnki.jmst.2018.04.003.
    [10] 张宪堂, 马力, 余辉, 等. 空孔直径对有围压直眼掏槽爆破破碎效果的影响 [J]. 煤炭科学技术, 2023, 51(10): 55–64. DOI: 10.13199/j.cnki.cst.2022-1357.

    ZHANG X T, MA L, YU H, et al. Influence of diameter of empty hole on the fragmentation effect of parallel cut blasting under confining pressure [J]. Coal Science and Technology, 2023, 51(10): 55–64. DOI: 10.13199/j.cnki.cst.2022-1357.
    [11] ZHOU Z L, WANG P Y, CHENG R S, et al. Blast-induced damage and fracture of rock mass in cutting blasting with a large empty hole under high in-situ stress [J]. Tunnelling and Underground Space Technology, 2025, 166: 106942. DOI: 10.1016/j.tust.2025.106942.
    [12] 岳中文, 郭洋, 王煦, 等. 空孔形状对岩石定向断裂爆破影响规律的研究 [J]. 岩土力学, 2016, 37(2): 376–382. DOI: 10.16285/j.rsm.2016.02.009.

    YUE Z W, GUO Y, WANG X, et al. Influence of empty hole shape on directional fracture controlled blasting of rock [J]. Rock and Soil Mechanics, 2016, 37(2): 376–382. DOI: 10.16285/j.rsm.2016.02.009.
    [13] QIN H F, ZHAO Y, WANG H L, et al. Damage prediction and improvement method based on cutting mode of circular empty hole [J]. Scientific Reports, 2024, 14(1): 11322. DOI: 10.1038/s41598-024-61599-x.
    [14] CHAI X W, SHI S S, YAN Y F, et al. Key blasting parameters for deep-hole excavation in an underground tunnel of phosphorite mine [J]. Advances in Civil Engineering, 2019, 2019: 4924382. DOI: 10.1155/2019/4924382.
    [15] CHANDRAKAR S, PAUL P S, SAWMLIANA C. Influence of void ratio on “Blast Pull” for different confinement factors of development headings in underground metalliferous mines [J]. Tunnelling and Underground Space Technology, 2021, 108: 103716. DOI: 10.1016/j.tust.2020.103716.
    [16] 黄飞飞, 缪玉松, 李昱锦, 等. 复式楔形超深孔掏槽爆破有效应力与损伤失效 [J]. 科学技术与工程, 2025, 25(27): 11833–11841. DOI: 10.12404/j.issn.1671-1815.2409403.

    HUANG F F, MIAO Y S, LI Y J, et al. Effective stress and damage failure of multi-wedge ultra-deep hole cut blasting [J]. Science Technology and Engineering, 2025, 25(27): 11833–11841. DOI: 10.12404/j.issn.1671-1815.2409403.
    [17] 王雁冰, 孔维文, 王国豪, 等. 深孔掏槽超深爆破破岩机制及最佳超深值研究 [J]. 采矿与安全工程学报, 2023, 40(6): 1210–1218. DOI: 10.13545/j.cnki.jmse.2022.0122.

    WANG Y B, KONG W W, WANG G H, et al. Mechanism of rock breaking by deep hole ultra-deep cut blasting and the optimum ultra-deep value determination [J]. Journal of Mining & Safety Engineering, 2023, 40(6): 1210–1218. DOI: 10.13545/j.cnki.jmse.2022.0122.
    [18] 黄永辉, 李永杰, 杨阳, 等. 露天爆破中炸药单耗对岩石破碎块度的数值模拟研究 [J]. 工程科学学报, 2024, 46(6): 973–981. DOI: 10.13374/j.issn2095-9389.2023.09.11.003.

    HUANG Y H, LI Y J, YANG Y, et al. Effect of explosive powder factor on rock crushing block size in open-pit blasting [J]. Chinese Journal of Engineering, 2024, 46(6): 973–981. DOI: 10.13374/j.issn2095-9389.2023.09.11.003.
    [19] 蔡静静, 徐轩, 陈占扬, 等. 孔内空气间隔对有/无金属罩聚能装药定向侵彻效果的影响 [J]. 含能材料, 2024, 32(7): 726–736. DOI: 10.11943/CJEM2023196.

    CAI J J, XU X, CHEN Z Y, et al. Effect of air gap in borehole on directional penetration of shaped charge with/without metal liner [J]. Chinese Journal of Energetic Materials, 2024, 32(7): 726–736. DOI: 10.11943/CJEM2023196.
    [20] JAYASINGHE L B, SHANG J L, ZHAO Z Y, et al. Numerical investigation into the blasting-induced damage characteristics of rocks considering the role of in-situ stresses and discontinuity persistence [J]. Computers and Geotechnics, 2019, 116: 103207. DOI: 10.1016/j.compgeo.2019.103207.
    [21] 程兵, 叶福, 汪泉, 等. 孔内分层装药爆破破岩成腔机理及应用 [J]. 含能材料, 2025, 33(7): 714–724. DOI: 10.11943/CJEM2025040.

    CHENG B, YE F, WANG Q, et al. Mechanisms of rock breaking and cavity formation of hole-inner layered charge blasting [J]. Chinese Journal of Energetic Materials, 2025, 33(7): 714–724. DOI: 10.11943/CJEM2025040.
    [22] 黄永辉, 占宇飞, 张洪波, 等. 极高地应力条件下光面爆破围岩损伤规律研究 [J]. 振动与冲击, 2025, 44(6): 104–112. DOI: 10.13465/j.cnki.jvs.2025.06.011.

    HUANG Y H, ZHAN Y F, ZHANG H B, et al. Damage patterns of surrounding rock under high-stress conditions in smooth blasting [J]. Journal of Vibration and Shock, 2025, 44(6): 104–112. DOI: 10.13465/j.cnki.jvs.2025.06.011.
    [23] 杨建华, 彭超, 叶志伟, 等. 深部岩体爆破冲击波能量分布特征 [J]. 兵工学报, 2024, 45(6): 1735–1746. DOI: 10.12382/bgxb.2023.0254.

    YANG J H, PENG C, YE Z W, et al. Energy distribution of shock wave in deep rock mass blasting [J]. Acta Armamentarii, 2024, 45(6): 1735–1746. DOI: 10.13465/j.bgxb.2023.0254. DOI: 10.12382/bgxb.2023.0254.
    [24] 于建新, 炊锦涛, 张浩, 等. 节理倾角与孔间参数对层状岩体爆破裂纹扩展的影响 [J]. 爆炸与冲击, 2025, 45(10): 101001. DOI: 10.11883/bzycj-2024-0463.

    YU J X, CHUI J T, ZHANG H, et al. Effect of joint dip angle and inter-hole parameters on blasting crack propagation in layered rock mass [J]. Explosion and Shock Waves, 2025, 45(10): 101001. DOI: 10.11883/bzycj-2024-0463.
    [25] 辛春亮, 薛再清, 涂建, 等. 有限元分析常用材料参数手册 [M]. 北京: 机械工业出版社, 2020.
    [26] 傅师贵, 刘泽功, 邱进伟, 等. 深部隧道切缝装药爆破岩体损伤演化及致裂特征 [J]. 工程科学学报, 2025, 47(6): 1191–1206. DOI: 10.13374/j.issn2095-9389.2024.07.09.002.

    FU S G, LIU Z G, QIU J W, et al. Study on the evolution of rock damage and blasting characteristics of deep tunnel splitting and drilling with explosives [J]. Chinese Journal of Engineering, 2025, 47(6): 1191–1206. DOI: 10.13374/j.issn2095-9389.2024.07.09.002.
    [27] 张鑫, 刘泽功, 常帅, 等. 爆破荷载作用下煤岩本构模型参数特性研究 [J]. 振动与冲击, 2025, 44(5): 263–277. DOI: 10.13465/j.cnki.jvs.2025.05.029.

    ZHANG X, LIU Z G, CHANG S, et al. Parametric characteristics of coal rock constitutive model under blasting load [J]. Journal of Vibration and Shock, 2025, 44(5): 263–277. DOI: 10.13465/j.cnki.jvs.2025.05.029.
    [28] 苗春贺, 陈丽娜, 单俊芳, 等. 水泥砂浆抗弹性能研究 [J]. 高压物理学报, 2021, 35(2): 024205. DOI: 10.11858/gywlxb.20200609.

    MIAO C H, CHEN L N, SHAN J F, et al. Research on the ballistic performance of cement mortar [J]. Chinese Journal of High Pressure Physics, 2021, 35(2): 024205. DOI: 10.11858/gywlxb.20200609.
  • 加载中
图(14) / 表(6)
计量
  • 文章访问数:  725
  • HTML全文浏览量:  70
  • PDF下载量:  72
  • 被引次数: 0
出版历程
  • 收稿日期:  2025-12-03
  • 修回日期:  2026-01-07
  • 网络出版日期:  2026-01-07

目录

    /

    返回文章
    返回