摘要:
为探究地铁隧道内爆炸荷载分布规律以及管片衬砌的损伤破坏和动态响应,首先以南京地铁S3号线某区间段为工程原型,建立了考虑覆土、道床、管片、手孔、螺栓和内部配筋等的足尺地铁隧道管片衬砌内爆炸精细化有限元模型。然后,基于显式动力学分析软件LS-DYNA对已有隧道中爆炸波传播试验和足尺管片衬砌内爆炸试验开展数值模拟,通过对比隧道壁面反射超压时程和管片衬砌损伤破坏等,充分验证了所采用有限元分析方法的适用性。进一步设计并开展了20组不同TNT当量(10~100kg)和装药位置(偏心和中心爆炸)的原型隧道管片衬砌内爆炸工况的数值仿真,分析了爆炸波在隧道内部的传播特征,建立了隧道轴向中心和壁面爆炸波峰值超压的计算公式。管片衬砌的变形和损伤破坏模式表明:(1)对于偏心爆炸:近爆区道床表面和管片接缝处损伤最严重;TNT当量小于30kg时,衬砌损伤以放射状裂纹为主;当量达到30kg时,近爆区管片接缝处混凝土开始碎裂;当量超过60kg后,衬砌破坏模式逐渐转变为近爆区管片接缝处混凝土碎裂、螺栓裸露和临近区域管片衬砌内外表面混凝土剥落;近爆区环向螺栓产生塑性拉伸变形且垫圈压碎,纵向螺栓在受拉的同时发生明显扭转;(2)对于中心爆炸:管片衬砌损伤破坏程度更轻且分布更均匀;TNT当量达到20kg时,衬砌出现裂纹,环向与纵向螺栓主要受拉;(3)100kg偏心和中心爆炸下隧道单侧衬砌环受损数量分别达到8和9个;(4)偏心和中心爆炸工况中,隧道管片衬砌最大径向峰值位移分别为92.3mm和18.66mm。本文工作可为隧道内爆炸荷载计算与抗爆设计提供一定参考。
Abstract:
Aimed to investigate the blast load distribution in a tunnel and the dynamic responses as well as damage and failure of the segmental lining, a refined full-scale finite element model of a subway tunnel was first established, taking a certain section of the Nanjing Metro Line S3 as the engineering prototype. The model incorporates overburden soil, track bed, segmental linings, handholes, bolts, and internal reinforcement. Subsequently, numerical simulations were conducted using the explicit dynamics analysis software LS-DYNA to reproduce existing blast wave propagation test in tunnels and prototype internal explosion tests in segmental linings. The applicability of the adopted finite element approach was thoroughly validated by comparing the reflected overpressure-time histories on the internal surface of the tunnel and the damage patterns of the segmental linings. Furthermore, a parametric numerical analysis was designed and performed for 20 internal explosion scenarios in the prototype tunnel, with TNT equivalent ranging from 10 kg to 100 kg and varying charge positions (eccentric and central detonations). The propagation characteristics of blast waves in the tunnel were revealed, and empirical formulae for predicting the peak overpressure at the tunnel axial center and on the internal surface of the tunnel were established. The deformation and damage of the segmental linings indicate that: (1) For eccentric explosions: The most severe damage occurs on the track bed surface and at the segment joints within the near-blast zone. When the TNT equivalent is less than 30 kg, the lining damage predominantly manifests as radial cracks. At an equivalent of 30 kg, concrete crushing initiates at the segment joints in the near-blast zone. When the equivalent exceeds 60 kg, the lining failure mode gradually transitions to concrete crushing at the segment joints in the near-blast zone, accompanied by exposed bolts, as well as concrete spalling on both the inner and outer surfaces of the segmental lining in adjacent areas. The circumferential bolts in the near-blast zone undergo plastic tensile deformation with crushed washers, while the longitudinal bolts experience notable torsion in addition to tensile loading. (2) For central explosions: The segmental lining sustains less severe damage with a more uniform distribution. Cracking appears in the lining when the TNT equivalent reaches 20 kg, and both the circumferential and longitudinal bolts are predominantly subjected to tension. (3) Under a 100 kg TNT equivalent, the numbers of damaged lining rings on a single side of the tunnel for eccentric and central explosions are 8 and 9, respectively. (4) In the eccentric and central explosion scenarios, the maximum peak radial displacements of the tunnel segmental lining are 92.3 mm and 18.66 mm, respectively. The findings of this work can serve as a useful reference for the calculation of internal blast loads and the blast-resistant design of tunnels.